Recent Posts

Pages: 1 ... 5 6 [7] 8 9 10
61
PLUS+1 Update Center / Update Center don't work V1.0.190
« Last post by rtapia on May 14, 2026, 05:32:15 PM »
Hello everybody...

i have a mistake with Update Center V1.0.190...

When i start the program and click to install Pluss1 or ServiceTool the desktop aplications send me to the web site for loggin ... after i logging, the website show me the message " Congratulations!, go to Plus1 tools (Desktop)...

Wherever when i come back to the update center... and clik on install button, the app send me again to the web site... to the en of time...

please someone can help me ? i need to install the plus1 again...
Thanks you

62
PLUS+1 Compliant Hardware / Re: JS6000 and JS1 Interoperability
« Last post by Lukey on May 14, 2026, 02:08:56 AM »
The JS6000 from factory is node id x34
The JS1-H from factory is node id X33

Maybe you are not seeing the node id's correctly, or because they are different from factory it does not work the same,

According to the JS6000 document 'JS6000 Joystick Base Technical Information'
"JS6000 joysticks do not support SAE J1939 dynamic addressing, since the joystick source addresses are hard-coded (static). However, JS6000 joysticks are compliant with SAE J1939 address claiming protocol (in the unlikely event another node on the SAE J1939 bus claims an identical source address to the JS6000, the JS6000 may cease communication on the bus, depending on the message priority of the other node)."



63
PLUS+1 Compliant Hardware / Re: JS6000 and JS1 Interoperability
« Last post by jraber on May 13, 2026, 05:02:48 PM »
I do see a number above the barcode on the JS1-H: 83070145

Regarding the addressing, I have confirmed using the CAN logging functionality of service tool that they are both pre-programmed to use address 0x33, and they are both sending the same PGNs. I don't see why they wouldn't be interchangeable, but supposedly the client is having issues.
64
PLUS+1 Compliant Hardware / Re: JS6000 and JS1 Interoperability
« Last post by Lukey on May 13, 2026, 05:33:30 AM »
Your JS6000 is 83018593https://powersource.danfoss.com/products/p/83018593
So it's a SAE J1939 type, with Node Id 0x34

JS1-H you'll have to find some more info on that, typically it will start with 11*******
https://powersource.danfoss.com/products/electronic-controls-hmi-and-iot/plus1-joysticks-and-foot-pedals/joysticks?hierarchy.level4=%22Electronic%20controls%2C%20HMI%2C%20and%20IoT%20%3E%20PLUS%2B1%C2%AE%20joysticks%20and%20foot%20pedals%20%3E%20Joysticks%20%3E%20JS1-H%20heavy-duty%20joysticks%22&tab=products
65
PLUS+1 Compliant Hardware / Re: JS6000 and JS1 Interoperability
« Last post by jraber on May 12, 2026, 04:46:19 PM »
JS6000-0126MK7, I also see JS6000-NY-CPL-F-S-FB-N-J341-A0BD-R-S-NNNNNNNR. The joystick has 2 tags on it, with serial numbers 18361744 and KD00029737.

JS1H, serial 32241157 (and that is all the info on the joystick)
66
PLUS+1 Compliant Hardware / Re: JS6000 and JS1 Interoperability
« Last post by Lukey on May 12, 2026, 05:30:30 AM »
What are the two materials No's?
67
PLUS+1 Compliant Hardware / JS6000 and JS1 Interoperability
« Last post by jraber on May 11, 2026, 07:08:04 PM »
Hello,

A client of mine is trying to physically use a JS1 in place of the obsoleted JS6000 and I am being told that it is not working. In our program we are using the JS6000_CANPlus block for handling this input, but I would think that all that is doing under the hood is parsing the raw CAN messages into an easy-to-use form. According to the data sheets of the JS6000 and the JS1 they use the same PGNs (0xFDD6, 0xFDD7), and I have verified this using the CAN logger in service tool. Same connector, same PGNs, so I would think it should be a plug-and-play upgrade, but apparently that is not the case (according to our client).

Does anyone have experience with this kind of hardware upgrade? Confirm or deny that it should "just work"?

Thanks,
JT
68
Controllers / Re: MC050-010 OBSOLETE
« Last post by samuelhj on May 07, 2026, 05:35:31 AM »
Quote from: Marbek_Elektronik on February 23, 2017, 11:15:14 AM
Please also check level on input pins.
If they are critical, you may have problems.
The thresholds are a little different.
We have had an application and the voltage levels were critical and by using MC050-010 we have had luck - it works.
By using MC050-100 our hardware produced error at the inputs:
We have send impulses to input pin and the voltage level was to high and some pulses were not counted.
So we optimized our hardware and MC050-100 worked well.

If your hardware-design is critical every change in hardware and software can produce errors!
So, check for good design everytime!

To add to that, the datasheet and the information within Guide can vary a bit, I've had that headache before, thankfully realising it early enough in the process, but I believe at least what i encountered has been updated.
69
Controllers / Re: Dynamic Node ID - Is this possible?
« Last post by Lukey on May 05, 2026, 04:39:02 AM »
It might be possible on a DM7/10/12 Display, as there is a reset/reboot/power cycle wire signal command.

On a controller/expansion module I don't think the above command is available.
70
Controllers / Dynamic Node ID - Is this possible?
« Last post by Mr.Jacobee on May 04, 2026, 08:37:10 AM »
Hello,

I would like to ask whether it is possible, from PLUS+1 GUIDE code or from an already compiled application, to reset or restart a CAN interface without performing a full power cycle.

The reason is that I need to change the Node ID of a specific CAN interface during operation. The application involves connecting two machines which normally operate independently, but in this case they need to be linked together and behave as one machine in a Master-Slave configuration.

Ideally, I would like to change the Node ID and then restart or reinitialize only the CAN interface, so the new configuration becomes active without switching the whole controller off and on again.

Is this possible in PLUS+1 GUIDE, or is a full power cycle required for the CAN interface to apply the new Node ID?

Thank you for any advice or experience.
Pages: 1 ... 5 6 [7] 8 9 10
This website uses cookies We and our partners use technologies, including cookies, to collect information about you for various purposes, including: Functionality, Statistics, Marketing By clicking 'Accept All' you consent to all these purposes. You can also choose to indicate what purposes you will consent to using the [Check boxes], then press 'Update consent'. You can always withdraw your consent by [clicking the small icon in the lower left corner of the page]. Detailed cookie information cannot be displayed if a cookie has been set behind a log-in webpage. However, the provided cookie consent prior to a log-in webpage is still applicable. You can read more about our use of cookies and other technologies, as well as our collection and processing of personal data by clicking on the link. Learn more